Ultrasonic sensor UC500-30GM-E7R2-V15
Brand: Pepperl+Fuchs
Code: UC500-30GM-E7R2-V15
Single head system, Parameterization interface for the application-specific adjustment of the sensor setting via the service program ULTRA 3000, 2 programmable switch outputs, Hysteresis mode selectable, Series: -30GM, Operating voltage: 10 ... 30 V DC , ripple 10 %SS, Interface type: RS 232, 9600 Bit/s , no parity, 8 data bits, 1 stop bit, Output type: 2 switch outputs NPN, NO/NC, programmable, UL approval: cULus Listed, General Purpose
Datasheet excerpt: Technical data of UC500-30GM-E7R2-V15
Product Description |
---|
Single head system |
General specifications | ||
---|---|---|
Sensing range | 30 ... 500 mm | |
Adjustment range | 50 ... 500 mm | |
Dead band | 0 ... 30 mm | |
Standard target plate | 100 mm x 100 mm | |
Transducer frequency | approx. 380 kHz | |
Response delay | 21 ms minimum 63 ms factory setting | |
Indicators/operating means | ||
LED green | solid: Power-on flashing: Standby mode or program function object detected | |
LED yellow 1 | solid: switching state switch output 1 flashing: program function | |
LED yellow 2 | solid: switching state switch output 2 flashing: program function | |
LED red | solid: temperature/program plug not connected flashing: fault or program function object not detected | |
Temperature/TEACH-IN connector | Temperature compensation , Switch points programming , output function setting | |
Electrical specifications | ||
Operating voltage | 10 ... 30 V DC , ripple 10 %SS | |
No-load supply current | ≤ 50 mA | |
Interface | ||
Interface type | RS 232, 9600 Bit/s , no parity, 8 data bits, 1 stop bit | |
Input/Output | ||
Synchronization | bi-directional 0 level -UB...+1 V 1 level: +4 V...+UB input impedance: > 12 KOhm synchronization pulse: ≥ 100 µs, synchronization interpulse period: ≥ 2 ms | |
Synchronization frequency | ||
Common mode operation | max. 95 Hz | |
Multiplex operation | ≤ 95 Hz / n , n = number of sensors , n ≤ 5 | |
Output | ||
Output type | 2 switch outputs NPN, NO/NC, programmable | |
Rated operating current | 200 mA , short-circuit/overload protected | |
Voltage drop | ≤ 2.5 V | |
Repeat accuracy | ≤ 0.1 % of full-scale value | |
Switching frequency | ≤ 7 Hz | |
Range hysteresis | 1 % of the adjusted operating range (default settings), programmable | |
Temperature influence | ≤ 2 % from full-scale value (with temperature compensation) ≤ 0.2 %/K (without temperature compensation) | |
Compliance with standards and directives | ||
Standard conformity | ||
Standards | EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 | |
Approvals and certificates | ||
UL approval | cULus Listed, General Purpose | |
CCC approval | CCC approval / marking not required for products rated ≤36 V | |
Ambient conditions | ||
Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) | |
Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
Mechanical specifications | ||
Connection type | Connector plug M12 x 1 , 5-pin | |
Housing diameter | 30 mm | |
Degree of protection | IP65 | |
Material | ||
Housing | stainless steel (1.4305 / AISI 303) PBT plastic parts | |
Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam | |
Mass | 140 g | |
Factory settings | ||
Output 1 | Switching point: 60 mm output function: Switch point operation mode output behavior: NO contact | |
Output 2 | Switching point: 500 mm output function: Switch point operation mode output behavior: NO contact |
Classifications
System | Classcode |
---|---|
ECLASS 13.0 | 27272803 |
ECLASS 12.0 | 27272803 |
ECLASS 11.0 | 27272803 |
ECLASS 10.0.1 | 27272803 |
ECLASS 9.0 | 27272803 |
ECLASS 8.0 | 27272803 |
ECLASS 5.1 | 27272803 |
ETIM 9.0 | EC001849 |
ETIM 8.0 | EC001849 |
ETIM 7.0 | EC001849 |
ETIM 6.0 | EC001849 |
ETIM 5.0 | EC001849 |
UNSPSC 12.1 | 41111960 |
Check out any spare parts and components from the Pepperl+Fuchs catalog!
Do you want to order a Ultrasonic sensor UC500-30GM-E7R2-V15 with code: UC500-30GM-E7R2-V15?
Leave your request on our website for immediate assistance!