Ultrasonic sensor UCC4000-50GK-B26-8MOL
Brand: Pepperl+Fuchs
Code: UCC4000-50GK-B26-8MOL
Single head system, Thread M50, PTFE coated transducer, Power save mode, Series: -50GK, Operating voltage: for UART and PWM operation:
UUART/PWM = 2.5 ... 5 V DC, typical 3.3 V
for LIN operation:
ULIN = 8 ... 18 V DC, typical 12 V, Interface type: Physical LIN interface, Interface type: UART 3.3V, Output type: PWM output (PNP) , not short-circuit protected, Connection type: fixed cable with plug, Housing: PBT, Connector: Molex connector 70107-0007
Datasheet excerpt: Technical data of UCC4000-50GK-B26-8MOL
| Product Description |
|---|
| Single head system |
| General specifications | ||
|---|---|---|
| Sensing range | 250 ... 4000 mm | |
| Dead band | 0 ... 250 mm | |
| Standard target plate | 100 mm x 100 mm | |
| Transducer frequency | approx. 75 kHz | |
| Electrical specifications | ||
| Operating voltage | for UART and PWM operation: UUART/PWM = 2.5 ... 5 V DC, typical 3.3 V for LIN operation: ULIN = 8 ... 18 V DC, typical 12 V | |
| No-load supply current | ≤ 60 mA at 3.3 V DC ≤ 20 mA at 12 V DC | |
| Quiescent current indication | < 3 µA during standby mode at UART- and PWM operation | |
| Power consumption | ≤ 250 mW in the measurement operating mode | |
| Time delay before availability | ≤ 95 ms | |
| Interface 1 | ||
| Interface type | Physical LIN interface | |
| Transfer rate | 19.2 kBit/s (8N1) | |
| Cycle time | 80 ms | |
| Resolution | 16 mm (corresponding to 1 LSB) | |
| Interface 2 | ||
| Interface type | UART 3.3V | |
| Transfer rate | 19.2 kBit/s (8N1) | |
| Cycle time | 80 ms | |
| Resolution | 16 mm (corresponding to 1 LSB) | |
| Input | ||
| Input type | Standby active | |
| Signal level | low: 0 ... 0.8 V | |
| Output | ||
| Output type | PWM output (PNP) , not short-circuit protected | |
| Resolution | pulse length 10 µs /cm | |
| Output rated operating current | max. 10 mA | |
| Temperature influence | 3 % of full-scale value over the entire temperature range | |
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN IEC 60947-5-2:2020 : chapter 8.2.6.2.2, 8.2.6.2.3, 8.2.6.3 The sensor is designed to be supplied by a battery. The sensor signals are further processed in a control unit, which is also responsible for EMC protection. | |
| Ambient conditions | ||
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) | |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Mechanical specifications | ||
| Connection type | fixed cable with plug | |
| Degree of protection | IP66 / IP67 ( connector excluded ) | |
| Material | ||
| Housing | PBT | |
| Transducer | epoxy resin/hollow glass bead mixture; Polyurethane foam, PTFE coated | |
| Connector | Molex connector 70107-0007 | |
| Number of pins | 8 | |
| Cable | ||
| Length | 276 mm ± 20 mm | |
| Mass | 100 g | |
| Factory settings | ||
| Output | PWM output (PNP) Temperature compensation Address setting 7 | |
| Beam width | wide | |
| General information | ||
| Scope of delivery | 2 nuts plastic | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27272803 |
| ECLASS 12.0 | 27272803 |
| ECLASS 11.0 | 27272803 |
| ECLASS 10.0.1 | 27272803 |
| ECLASS 9.0 | 27272803 |
| ECLASS 8.0 | 27272803 |
| ECLASS 5.1 | 27272803 |
| ETIM 9.0 | EC001849 |
| ETIM 8.0 | EC001849 |
| ETIM 7.0 | EC001849 |
| ETIM 6.0 | EC001849 |
| ETIM 5.0 | EC001849 |
| UNSPSC 12.1 | 41111960 |
Check out any spare parts and components from the Pepperl+Fuchs catalog!
Do you want to order a Ultrasonic sensor UCC4000-50GK-B26-8MOL with code: UCC4000-50GK-B26-8MOL?
Leave your request on our website for immediate assistance!
